New CAT Equipment

Cat 908 Compact Wheel Loader

Configured for Success

Cat® wheel loaders set the standard for productivity, fuel efficiency and operator comfort. The Cat 908 Compact Wheel Loader has a high torque C2.8 engine that works in conjunction with an intelligent hystat power train to deliver exceptional fuel efficiency. “Shift on the go” locking differentials and hydrostatic transmission provide smooth and powerful operation while increasing the efficiency of machine cycles.

Get a Quote

Benefits

60% Greater Wiper Coverage

all new cab with seat mounted controls and integrated display screen

40 kph (25 mph)

with "shift on the go" transmission

Customized

for application specific configurations including factory and aftermarket options

Learn more about the Cat 908 Compact Wheel Loader

Watch

  • Axles
    Front
    Fixed (standard), Locking Differential (optional)
    Note
    Oscillation of ±11 degrees via hitch between front and rear frames.
    Rear
    Fixed (standard), Locking Differential (optional)
  • Buckets
    Bucket Capacities
    0.75-1.55 m³ (1.0-2.0 yd³)
    Bucket Capacities - General Purpose
    0.80-1.35 m³ (1.0-1.7 yd³)
    Bucket Capacities - Light Material
    1.25-1.55 m³ (1.6-2.0 yd³)
    Multi-Purpose
    0.75-1.1 m³ (1.0-1.4 yd³)
    Note
    Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
    Note (1)
    Bucket capacities stated include BOCE, in line with ISO 7546.
  • Cab
    FOPS
    ISO 3449:2005 Level II
    Note (1)
    Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.
    ROPS
    ISO 3471:2008
  • Dimensions - High Lift - With HPL-V Coupler - Approximate#
    80% of Tip: Firm and Level EN474-3 ††
    4706 lb
    Articulation Angle - Degrees
    39°
    Carry Height: Bucket Pin
    1.17 ft
    Clearance: Bucket at 45° *
    10.92 ft
    Clearance: Level Bucket**
    12.08 ft
    Clearance: Load over Height**
    10.75 ft
    Departure Angle - Degrees
    30°
    Dig Depth**
    0.33 ft
    Dump Angle at Full Lift
    40°
    Height: Bucket Pin**
    12.75 ft
    Height: Ground Axle Center**
    1.67 ft
    Height: Ground Clearance**
    1 ft
    Height: Ground to Beacon**
    9.33 ft
    Height: Ground to Cab**
    8.75 ft
    Height: Overall**
    15.67 ft
    Length: Hitch to Front Axle
    3.5 ft
    Length: Overall*
    19.67 ft
    Length: Rear Axle to Bumper
    4.5 ft
    Length: Wheel Base
    7.08 ft
    Note (1)
    *Vary with bucket
    Note (2)
    **Vary with tire
    Note (3)
    Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
    Note (4)
    ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
    Note (5)
    †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
    Note (6)
    ††Full compliance to EN474-3 and SAE J1197.
    Note (7)
    #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
    Note (8)
    Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
    Note (9)
    Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9
    Operating Weight: Bucket ^
    14848 lb
    Operating Weight: Carriage and Tines ^^
    14542 lb
    Rack Angle at Carry
    48°
    Rack Angle at Full Lift
    69°
    Reach: Bucket at 45° *
    3.25 ft
    Tipping Load - Full Turn - ISO 14397-1 †
    7645 lb
    Tipping Load - Straight - ISO 14397-1 †
    9187 lb
    Tipping Load - Straight †
    9187 lb
    Turning Radius: Inside of Tires
    6.5 ft
    Turning Radius: Outside of Tires
    13.17 ft
    Turning Radius: Over Bucket
    15.83 ft
    Width: Bucket
    6.75 ft
    Width: Over Tires
    6.67 ft
    Width: Tread Center
    5.08 ft
  • Dimensions - High Lift - With SSL Coupler - Approximate
    80% of Tip: Firm and Level EN474-3 ††
    4375 lb
    Articulation Angle - Degrees
    39°
    Carry Height: Bucket Pin
    1.25 ft
    Clearance: Bucket at 45° *
    10.42 ft
    Clearance: Level Bucket**
    12.08 ft
    Clearance: Load over Height**
    10.75 ft
    Departure Angle - Degrees
    30°
    Dig Depth**
    0.42 ft
    Dump Angle at Full Lift
    40°
    Height: Bucket Pin**
    12.75 ft
    Height: Ground Axle Center**
    1.67 ft
    Height: Ground Clearance**
    1 ft
    Height: Ground to Beacon**
    9.33 ft
    Height: Ground to Cab**
    8.75 ft
    Height: Overall**
    15.92 ft
    Length: Hitch to Front Axle
    3.5 ft
    Length: Overall*
    20.17 ft
    Length: Rear Axle to Bumper
    4.5 ft
    Length: Wheel Base
    7.08 ft
    Note (1)
    *Vary with bucket
    Note (2)
    **Vary with tire
    Note (3)
    ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
    Note (4)
    ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
    Note (5)
    †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
    Note (6)
    ††Full compliance to EN474-3 and SAE J1197.
    Note (7)
    #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
    Note (8)
    Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
    Note (9)
    Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9
    Operating Weight: Bucket ^
    15070 lb
    Operating Weight: Carriage and Tines ^^
    14714 lb
    Rack Angle at Carry
    42°
    Rack Angle at Full Lift
    66°
    Reach: Bucket at 45° *
    3.42 ft
    Tipping Load - Full Turn - ISO 14397-1 †
    6943 lb
    Tipping Load - Straight - ISO 14397-1 †
    8385 lb
    Tipping Load - Straight †
    8385 lb
    Turning Radius: Inside of Tires
    6.5 ft
    Turning Radius: Outside of Tires
    13.17 ft
    Turning Radius: Over Bucket
    16.17 ft
    Width: Bucket
    6.75 ft
    Width: Over Tires
    6.67 ft
    Width: Tread Center
    5.08 ft
  • Dimensions - With HPL-V Coupler - Approximate#
    80% of Tip: Firm and Level EN474-3 ††
    5815 lb
    Articulation Angle - Degrees
    39°
    Carry Height: Bucket Pin
    1.17 ft
    Clearance: Bucket at 45° *
    8.58 ft
    Clearance: Level Bucket**
    10.5 ft
    Clearance: Load over Height**
    9.75 ft
    Departure Angle - Degrees
    30°
    Dig Depth**
    0.33 ft
    Dump Angle at Full Lift
    45°
    Height: Bucket Pin**
    11.17 ft
    Height: Ground Axle Center**
    1.67 ft
    Height: Ground Clearance**
    1 ft
    Height: Ground to Beacon**
    9.33 ft
    Height: Ground to Cab**
    8.75 ft
    Height: Overall**
    14.17 ft
    Length: Hitch to Front Axle
    3.5 ft
    Length: Overall*
    18.17 ft
    Length: Rear Axle to Bumper
    4.5 ft
    Length: Wheel Base
    7.08 ft
    Note (1)
    *Vary with bucket
    Note (2)
    **Vary with tire
    Note (3)
    ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
    Note (4)
    ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
    Note (5)
    †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
    Note (6)
    ††Full compliance to EN474-3 and SAE J1197.
    Note (7)
    #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
    Note (8)
    Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
    Note (9)
    Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9
    Operating Weight: Bucket ^
    14633 lb
    Operating Weight: Carriage and Tines ^^
    14252 lb
    Rack Angle at Carry
    51°
    Rack Angle at Full Lift
    53°
    Reach: Bucket at 45° *
    2.33 ft
    Tipping Load - Full Turn - ISO 14397-1 †
    8895 lb
    Tipping Load - Straight - ISO 14397-1 †
    10626 lb
    Tipping Load - Straight †
    10626 lb
    Turning Radius: Inside of Tires
    6.5 ft
    Turning Radius: Outside of Tires
    13.17 ft
    Turning Radius: Over Bucket
    14.75 ft
    Width: Bucket
    6.75 ft
    Width: Over Tires
    6.67 ft
    Width: Tread Center
    5.08 ft
  • Dimensions - With SSL Coupler - Approximate
    80% of Tip: Firm and Level EN474-3 ††
    5438 lb
    Articulation Angle - Degrees
    39°
    Carry Height: Bucket Pin
    1.25 ft
    Clearance - Bucket at 45°
    8.25 ft
    Clearance - Level Bucket
    10.5 ft
    Clearance: Load over Height**
    9.75 ft
    Departure Angle - Degrees
    30°
    Dig Depth
    0.45 ft
    Dump Angle at Full Lift
    48°
    Height - Bucket Pin
    11.17 ft
    Height - Ground Clearance
    1 ft
    Height - Ground to Cab
    8.75 ft
    Height: Ground Axle Center**
    1.67 ft
    Height: Ground to Beacon**
    9.33 ft
    Height: Overall**
    14.42 ft
    Length - Overall with Bucket
    18.67 ft
    Length - Wheel Base
    7.08 ft
    Length: Front Axle to Front of Coupler
    4.75 ft
    Length: Hitch to Front Axle
    3.5 ft
    Length: Rear Axle to Bumper
    4.5 ft
    Note (1)
    *Vary with bucket
    Note (2)
    **Vary with tire
    Note (3)
    ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
    Note (4)
    ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
    Note (5)
    †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
    Note (6)
    ††Full compliance to EN474-3 and SAE J1197.
    Note (7)
    #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
    Note (8)
    Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
    Note (9)
    Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9
    Operating Weight: Bucket ^
    14752 lb
    Operating Weight: Carriage and Tines ^^
    14391 lb
    Rack Angle at Carry
    54°
    Rack Angle at Full Lift
    50°
    Reach - Bucket at 45°
    2.67 ft
    Tipping Load - Full Turn - ISO 14397-1†
    6800 lb
    Tipping Load - Straight †
    9753 lb
    Tipping Load – Full Turn – ISO 14397-1 †
    8141 lb
    Tipping Load – Straight – ISO 14397-1 †
    9581 lb
    Turning Radius - Inside Tire
    6.67 ft
    Turning Radius - Over Bucket
    15.08 ft
    Turning Radius: Outside of Tires
    13.17 ft
    Width - Bucket
    6.75 ft
    Width - Over Tires
    6.67 ft
    Width - Tread Center
    5.08 ft
  • Engine
    Bore
    3.54 in
    Displacement
    171 in³
    Engine Model
    Cat C2.8*
    Maximum Engine Speed
    2550 rpm
    Maximum Gross Power
    74.7 hp
    Maximum Gross Power - ISO 14396
    74.3 hp
    Maximum Gross Power - ISO 14396 (metric)
    75.3 mhp
    Maximum Gross Power - Rated Engine Speed
    2400 r/min
    Maximum Gross Power - SAE J1995
    74.7 hp
    Maximum Gross Torque - ISO 14396
    221 lb/ft
    Maximum Gross Torque - SAE J1995
    222 lb/ft
    Maximum Net Torque - ISO 9249
    217 lb/ft
    Maximum Net Torque - SAE J1349
    218 lb/ft
    Note
    Advertised power is tested per the specified standard in effect at the time of manufacture
    Note (1)
    Net power advertised is the power available at the flywheel.
    Note (2)
    *Two Cat C2.8 engine emission options are available: 1) Meets U.S. EPA Tier 4 Final, EU Stage V. 2) U.S. EPA Tier 3 and EU Stage IIIA equivalent. Tier 3 engine specs are 0.3 kW/0.4 hp more gross power (SAE J1995), 0.2 kW/0.3 hp on net power (SAE J1349) and 1 N·m/0.7 lb-ft higher on gross torque (SAE J1995).
    Note (3)
    #Maximum gross and net torque measured at 1,600 rpm.
    Rated Net Power - 2,400 rpm - ISO 9249 (metric)
    73.1 mhp
    Rated Net Power - ISO 9249
    72.1 hp
    Rated Net Power - Rated Engine Speed
    2400 r/min
    Rated Net Power - SAE J1349
    72.7 hp
    Stroke
    4.33 in
  • Loader Hydraulic System
    Hydraulic Cycle Time - Dump
    1.8 s
    Hydraulic Cycle Time - Float Down
    3.6 s
    Hydraulic Cycle Time - Lift
    5.8 s
    Hydraulic Cycle Time - Rackback
    2.5 s
    Main Relief - 1st Auxiliary (3rd slice)
    3408 psi
    Main Relief - 1st Auxiliary (3rd slice) - High Flow*
    33 gpm
    Main Relief - 1st Auxiliary (3rd slice) - Standard Flow*
    24 gpm
    Main Relief - 2nd Auxiliary (4th slice)
    3408 psi
    Main Relief - 2nd Auxiliary (4th slice) - Flow
    12 gpm
    Note
    * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.
  • Service Refill Capacities
    Axles - Front Center Differential
    2.3 Gal
    Axles - Rear Center Differential
    2.3 Gal
    Cooling System
    3.2 gal (US)
    Engine Crankcase
    2.3 Gal
    Fuel Tank
    24 Gal
    Hydraulic System - Including Tank
    18.6 Gal
    Hydraulic Tank
    11.8 gal (US)
    Note
    No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.
    Transmission
    0.6 Gal
  • Steering
    Maximum Flow - Steering Pump
    12.3 gpm
    Maximum Working Pressure - Steering Pump
    3336 psi
    Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
    3.25 turns or 4.00 turns
    Steering Articulation Angle - Each Direction
    39 °
    Steering Cycle Times – (full left to full right) – at High Idle
    2.8 s
  • Sustainability
    Recyclability
    93%
  • Tires
    Note
    *This tire has been used for all dimension, stability and performance data.
    Note (1)
    Other tire choices are available. Contact your Cat dealer for details.
    Note (2)
    Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
    Tire Size - Optional
    405/70 R20 Powerloads
    Tire Size - Optional (1)
    400/70 R20 XMCL/Bibload
    Tire Size - Optional (2)
    360/80 R20 TRI 2
    Tire Size - Optional (3)
    40X14-20 TL, SM/TR
    Tire Size - Standard
    *405/70 R20 SPT9
  • Transmission
    Forward and Reverse - Speed Range 1*
    6 mile/h
    Forward and Reverse - Speed Range 2** - High Speed
    10.5 mile/h
    Forward and Reverse - Speed Range 2** - Standard
    12 mile/h
    Forward and Reverse - Speed Range 3***
    25 mile/h
    Forward and Reverse - Speed Range Creep#
    6 mile/h
    Note
    #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).
    Note (1)
    *Creep function not available in this gear or above.
    Note (2)
    **Max speed dependent on model and configuration (standard vs. high speed transmission).
    Note (3)
    ***Reverse is 30 km/h (19 mph).
POWER TRAIN
  • Emissions compliant, two options (Dependent on regional regulations.)
    – U.S. EPA Tier 4 Final and EU Stage V
    – U.S. EPA Tier 3 and EU Stage IIIA equivalent
  • Cat C2.8 engine
    – Diesel particulate filter (Fit for Life) or muffler (Dependent on regional regulations.)
    – Fuel, diesel, ultra low or low Sulphur (Dependent on regional regulations.)
    – Hydrostatic transmission, two speed, with inching function, “shift on the go”
    – Power train mode, hystat
  • Air cleaner, two stage filter, with in cab audio/visual indicator on display
  • Axles, heavy duty, frame mounted with outboard planetary reduction
  • Closed circuit breather
  • Coolant, extended life, –36° C (–33° F)
  • Drive shaft, sealed for life, universal joints
  • Engine, auto idle shutdown, hibernation mode
  • Engine oil, ECO drain tap and hose
  • Fuel pump, priming (manual)/water separator/drain
HYDRAULICS
  • Hydraulic pilot shut off switch, in cab
  • Electro-hydraulic, fully proportional controls
  • Dead engine lower, lift valve, manual
  • Demand cooling fan, hydraulically drive
  • Coupler/pin on attachment ready
  • Caterpillar HYDO™ Advanced 10 hydraulic oil
  • Hystat displacement pump, infinitely variable
  • Implement valve, pressure compensated
  • Joystick, single lever, single auxiliary roller
  • Multi-function lift and tilt with loader arm float
  • Motor, single drive with dedicated implement and steering pumps
ELECTRICAL
  • Alternator, 100 amp sealed
  • Battery, heavy duty, 12V, 90Ah and 1,000 CCA
  • Battery disconnect switch
  • Cab mounted fuse panel
  • Lights, rear stop and turn, LED
  • Lights, roading, front halogen
  • Service (Electronic Technician™)
  • Product Link™
OPERATOR ENVIRONMENT
  • ROPS/FOPS certified canopy/cab
    – 12V power outlets, interior/exterior
    – Pedals, raised, foot, brake/inching, accelerator
    – Lever, parking brake
    – Cup holders (2)
    – CB radio clip, phone holder
    – Door release, internal (left and right)
    – Hook, large, coat and hard hat
    – Floormat, heavy duty, easy clean
    – Mirrors, (2) external breakaway, (1) internal
    – Operator station on isolation mounts
    – Steering wheel, spinner knob, horn in center
    – Seat belt, orange, retractable, 51 mm (2 in)
    – Storage, personal (trays [3], seat pocket)
    – Steering column, tilt adjusted
    – Column mounted multi function control: lights, roading, wipers, self cancelling turn signals
    – Quick coupler switch, in cab
  • Display, analog and digital
    – Gauges (2), hydraulic oil, engine coolant
    – Digital with soft touch buttons – fuel level, speed range, speedometer, service hour meter, service/maintenance information, hydraulic and power train performance and aggressiveness settings, security passcode (multiple languages)
  • Joystick, seat mounted, standard multifunction
    – FNR, auxiliary roller, speed range select, continuous flow, differential lock, horn
    – Arm rest, padded right, multiple position vertical height
  • Seat, manual height adjustment, (cab) fabric with adjustable left arm rest, (canopy) vinyl
  • Cab
    – Doors (2), fixed glass
    – Wipers, front and rear, full front coverage
    – Windshield, front single piece
    – Window, rear heated
    – Radio ready, speakers and wiring
    – Air vents, (4) screen, (7) directional
    – Heating, mechanical control unit
    – Sun visor, solid, front full width
    – Interior light (incandescent)
OTHER
  • Fenders, front and rear
  • Ground level easy access daily service points
  • Loader arm safety brace
  • Lockable main and side engine enclosures
  • Lockable, fuel cap, HVAC filters, nose cone
  • Machine lifting/tie down points
  • Paint, Electro-Coat primer, gloss topcoat
  • Recovery hitch with pin
  • Scheduled Oil Sampling (S·O·S℠) ports, engine oil and hydraulic oil
POWER TRAIN
  • Antifreeze, extended life coolant, –50° C (–58° F)
  • Cold start – jacket water heater, bypass valve
  • Creep and throttle lock function
  • Fuel pump, priming, electric (Dependent on regional regulations.)
  • 40 km/h (25 mph) hydrostatic transmission, 3-speed, “shift on the go”, secondary steering and boosted brakes
  • Power train mode, utility (includes keypad)
ELECTRICAL
  • Lighting packages, multiple; front, rear, engine bay (LED or HAL)
  • Push to start
  • Work tool wiring harness, (3) in cab switches
HYDRAULICS
  • Auxiliary flow, single standard (3) valve, single high flow (3) valve, dual high flow (4) valve
  • Caterpillar Bio HYDO Advanced hydraulic oil
  • Connect under pressure and case drain
  • Ride Control or load check valves*
  • Reversing fan
  • Quick disconnect auxiliary hydraulics
OPERATOR STATION
  • Air Conditioning, automatic temperature control (ATC)
  • Doors, sliding windows (left and right)
  • Interior light, door activated
  • Joystick, FNR, twin auxiliary roller, differential lock, horn
  • Joystick, seat mounted, multifunction
  • Mirrors (2) electronically adjustable, heated external, plus lower parabolic mirror
  • Phone holder, spring loaded
  • Radio, FM or digital audio broadcast
  • Seat belt options, multiple
  • Seat packages; deluxe or premium
  • Secondary display, front or rear view camera
  • Soft touch keypad options, 8 or 16 button
  • Storage, lockable box or lockable cooled box
  • Sun visor, rear perforated
  • USB ports (2), interior
OTHER
  • Couplers, vertical (SSL), horizontal (HPL-V, HPL-A)
  • Rotary sensors (snubbing, kickouts, parallel)
  • High lift option

Download Resources

Site Map Legal Terms Privacy Policy Your Privacy Choices California Collection Notice Cookie Policy
Copyright © 2026 Fabick Cat | All Rights Reserved.

Fabick Cat & Fabick Cat Rentals are not affiliated with Fabick, Inc. Click here for more information.