New CAT Equipment

920 Compact Wheel Loader

The Cat® 920 Compact Wheel Loader features a C3.6 engine, the Cat Optimized Z-bar Loader linkage, various work tools, a state-of-the-art electro-hydraulic system, a tuned drivetrain, a cab with all-around visibility, extended service intervals and excellent service access, and standard fuel savings features.

Get a Quote

Learn more about the 920 Compact Wheel Loader

Watch

Product Specs

Engine

Maximum Gross Power 121 HP
Bore 3.86 in
Stroke 4.72 in
Displacement 220 in³
Maximum Gross Power - Maximum Engine Speed 2350 r/min
Emissions Engine meets Tier 4 Final/Stage V emission standards.
Note Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
Rated Net Power - Rated Engine Speed 2200 r/min
Rated Net Power - SAE J1349 120 HP
Maximum Gross Power - ISO 14396 (DIN) 122 HP
Maximum Gross Power - ISO 14396 121 HP
Maximum Gross Torque - SAE J1995 372 ft·lbf
Engine Model Cat C3.6
Maximum Gross Power - SAE J1995 123 HP
Rated Net Power - ISO 9249 (DIN) 120 HP
Rated Net Power - ISO 9249 118 HP
Maximum Gross Torque - ISO 14396 369 ft·lbf
Maximum Net Torque - ISO 9249 363 ft·lbf
Maximum Net Torque - SAE J1349 366 ft·lbf

Weights

Operating Weight 21742 lb

Buckets

Bucket Capacities 1.3-1.9 m³ (1.7-2.5 yd³)
Bucket Capacities - General Purpose 1.3-1.9 m³ (1.7-2.5 yd³)
Bucket Capacities - Light Material 2.5-3.5 m³ (3.3-4.6 yd³)

Steering

Maximum Working Pressure - Steering Pump 3190 psi
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed 2.3 s
Steering Articulation Angle - Each Direction 40 °
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left 3.4 turns
Maximum Flow - Steering Pump 21.7 gal/min

Loader Hydraulic System

Relief Pressure - Tilt Cylinder 4641 psi
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard 25 gal/min
Maximum Flow - Implement Pump 43.6 gal/min
Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure 4641 psi
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level 2.7 s
Note All cycle times listed are with cylinder snubbing turned off.
Maximum Working Pressure - Implement Pump 4061 psi
Hydraulic Cycle Time - Total Cycle Time 11.5 s
Hydraulic Cycle Time - Rackback 2.2 s
Maximum Flow - Implement Pump - 4rd Function, Maximum Flow 25 gal/min
Hydraulic Cycle Time - Dump, at Maximum Reach 1.8 s
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift 4.8 s
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High 40 gal/min

Service Refill Capacities

Transmission 0.8 gal (US)
Engine Crankcase 2.6 gal (US)
Diesel Exhaust Fluid (DEF) Tank 4.8 gal (US)
Axles - Rear 4.5 gal (US)
Cooling System 5.7 gal (US)
Hydraulic System - Including Tank 25.9 gal (US)
Axles - Front 4.5 gal (US)
Fuel Tank 43.6 gal (US)
Hydraulic Tank 14.5 gal (US)
Note DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.

Transmission

Note *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
Forward and Reverse - Speed Range 3 25 mile/h
Forward and Reverse - Speed Range 2* 12.5 mile/h
Forward and Reverse - Speed Range 1* 6.3 mile/h

Axles

Rear Oscillating ±11 degrees; Locking differential (standard)
Front Fixed; Locking differential (standard)

Cab

ROPS ISO 3471:2008
FOPS EN ISO 3449:2008 (ISO 3449:2005)
Note (3) The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A).
Note (2) The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A).
Note (1) Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
Note (4) *The measurements were conducted with the cab doors and windows closed.

Tires

Other Choices Include 17.5 R25 L3 XHA2; 20.5 R25 L3 XHA3; 17.5-25 L2/L3 SGL; 20.5-25 L2/L3 SGL; 17.5-25 L3 HRL D/L-3A; 17.5 R25 L2 Snow; 20.5 R25 L2 Snow; 17.5 R25 Solid
Standard Size 17.5 R25 L2 XTLA
Note (1) Other tire choices are available. Contact your Cat dealer for details.
Note (3) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Note (2) In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.