New CAT Equipment

794 AC Mining Truck

Designed and manufactured by Caterpillar, the 794 AC electric drive truck is single sourced from one manufacturer and supported by the best dealer network. The 794 AC is designed to:

  • Deliver a true 297 tonnes (327 tons) capacity
  • Deliver reliability and uptime
  • Deliver easy serviceability
  • Deliver low owning and operating cost
  • Deliver operator confidence with four corner wet disc blended service brakes and traction control
The 794 AC is built to deliver to your bottom line.

Get a Quote

    Learn more about the 794 AC Mining Truck

    Watch

    Product Specs

    Engine

    Gross Power - SAE J1995 3500 HP
    Standard Gross Power - SAE J1995 3500 HP
    Engine Model Cat® C175-16
    Optional Gross Power - SAE J1995 3100 HP
    Optional Gross Power - SAE J1995 (Option 2) 2750 HP
    Rated Speed 1800 r/min
    Net Power - SAE J1349 3405 HP
    Emissions Rating Fuel Optimized
    Bore 6.9 in
    Stroke 8.7 in
    Displacement 5187 in³
    Note (1) Contact factory for high altitude configuration.
    Note (2) Tier 4 / EU Stage V option available for regions that require these emissions standards.
    Note (3) Tier 4 / EU Stage V engine option Net Power - SAE J1349: 3434 HP (2561 kW)

    Weights - Approximate

    Nominal Rated Payload 327 ton (US)
    Rated Gross Machine Weight 1150000 lb
    Chassis Weight 426237 lb
    Body Weight 64346 lb
    Note (1) Consult your tire manufacturer for maximum tire load.
    Note (2) Chassis weight with full fuel and fluids, standard & mandatory attachments, hoist, body mounting group, rims, and tires
    Note (3) Refer to Cat Mining Truck 10/10/20 Overload Policy (AEXQ0250) for maximum gross machine weight limitations.
    Note (4) Tier 4 Final / Stage V chassis weight: 426312 lb (193372 kg)

    Final Drives

    Total Reduction Ratio 35:1

    AC Drive System

    Total Reduction Ratio 35:1
    Top Speed - Loaded 37 mile/h
    Generator/Alternator Brushless, engine mounted, dual bearing
    Controls IGBT Inverter Technology, air cooled, pressurized cabinet with filtration
    Wheel Motor High-torque AC induction, rear axle mounted
    Cooling System Variable speed, hydraulically driven cooling system

    Tires

    Standard Tires 53/80 R63
    Rims 36" x 63"
    Note (1) Quick Change Rims optional.
    Note (2) Caterpillar recommends the customer evaluate all job conditions and consult tire manufacturer for proper tire selection and TKPH (TMPH) capabilities.

    Braking System

    Service Brakes Four-Corner, Wet Disc, Oil Cooled, Hydraulically Actuated
    Front Wet Disc Brake Surface Area 20378 in²
    Rear - Wet Disc Brake Surface Area 30750 in²
    Standards ISO 3450:2011
    Parking Brake Four-corner, Multi-disc, Spring applied, Hydraulically Released
    Load Brake Rear service brakes
    Dynamic Retarding Power - Continuous 5480 HP

    Weight Distributions - Approximate

    Front Axle - Empty 49 %
    Rear Axle - Empty 51 %
    Front Axle - Loaded 33 %
    Rear Axle - Loaded 67 %

    Body Hoists

    Pump Flow - High Idle (HAA at 1,800 rpm) 221 gal/min
    Pump Flow - High Idle (LAA at 1,960 rpm) 240 gal/min
    Relief Valve Setting - Raise 3029 psi
    Body Raise Time - High Idle 24 s
    High Idle Body Lower Time - Float 20 s
    Total Cycle Time 44 s
    Note (1) Twin, two-stage hydraulic cylinders mounted inside main frame; double-acting cylinders in both stages.
    Note (2) Power raise in both stages; power down in both stages possible.
    Note (3) Automatic body-lower modulation reduces impact on frame.

    Capacity - HE Body - 100% fill factor

    Struck 108-133 m³ (142-175 yd³)
    Heaped (SAE 2:1) 180-222 m³ (236-290 yd³)
    Dump Body Plate Thickness Varies Depending on Body Selection - Floor Plate 0.63 in
    Dump Body Plate Thickness Varies Depending on Body Selection - Front Plate 0.35 in
    Dump Body Plate Thickness Varies Depending on Body Selection - Side Plate 0.31 in
    Dump Body Plate Thickness Varies Depending on Body Selection - Canopy Plate 0.2 in
    Note Contact your local Cat dealer for body recommendations.

    Service Refill Capacities

    Fuel Tank 1300 gal (US)
    Cooling System 211 gal (US)
    Crankcase 82 gal (US)
    Final Drive - Each 67 gal (US)
    Hydraulic Tank 296 gal (US)
    Hydraulic System - Including Tank 385 gal (US)
    Diesel Exhaust Fluid Tank 100 gal (US)
    Note (1) DEF Tank only available for EPA Tier 4 / EU Stage V engine option.

    ROPS

    ROPS Standards ROPS (Rollover Protective Structure) meets ISO 3471:1994.
    FOPS Standards FOPS (Falling Object Protective Structure) meets ISO 3449:1992.

    Sound

    Sound Standards (1) The operator sound pressure level measured according to work cycle procedures specified in ISO 6394 and 6396 is 75 dB(A) for cab offered by Caterpillar when properly installed, maintained, and tested with doors and windows closed.
    Sound Standards (2) Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.

    Steering

    Steering Standards ISO 5010:2007
    Note Gross Machine Operating Weight is 521 631 kg (1,150,000 lb).
    Steer Angle 39 °

    Dimensions (Approximate)

    Height - Top of ROPS 22.25 ft
    Overall Length 50.75 ft
    Wheel Base 21.83 ft
    Rear Axle - Tail 15.5 ft
    Ground Clearance 2.67 ft
    Dump Clearance 3 ft
    Loading Height - Empty 22.92 ft
    Overall Height - Body Raised 48.42 ft
    Centerline Front Tire Width 23 ft
    Front Axle Clearance 3.17 ft
    Canopy Width (without optional rock deflectors) 29.75 ft
    Outside Body Width 29.75 ft
    Inside Body Width 28.08 ft
    Front Canopy Height 26.33 ft
    Rear Axle - Clearance 3.08 ft
    Centerline of Rear Dual Tire Width 18.75 ft
    Overall Tire Width 28.67 ft
    Overall Canopy Width 31.5 ft