Engine Model | Cat C9.3 |
Bore | 4.5 in |
Stroke | 45.2 in |
Displacement | 567.5 in³ |
Peak Engine Torque Gross (SAE J1995) | 1275 ft·lbf |
Gross Power - SAE J1995 | 342 HP |
Net Power - ISO 14396 | 338 HP |
Engine Model - U.S. EPA Tier 4 Final/EU Stage IV | Cat® C9.3 |
No Engine De-rating Below | 3000 ft |
Peak Engine Torque Net (SAE J1349) | 1263 ft·lbf |
Net Power - SAE J1349 | 334 HP |
Peak Engine Torque Speed | 1200 r/min |
Note (1) | The power ratings apply at rated speed of 1,700 rpm when tested under the conditions for the specified standard. |
Emissions | The reference to Tier 4 Final/Stage IV includes U.S. EPA Tier 4 Final, EU Stage V, Japan 2014 (Tier 4 Final), as well as Korea Tier 4 Final emission standards. |
Note (3) | Net power when the fan is at maximum speed is 249 kW (334 hp) per the SAE reference conditions. |
Note (2) | The net power advertised is the power available at the flywheel when the engine is equipped with alternator, air cleaner, muffler and fan at minimum speed. |
Note (4) | DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. ISO 22241-1 requirements are met by many brands of DEF, including those that carry the AdBlue or API certifications. |
Rated Payload | 26.5 ton (US) |
Heaped (SAE 2:1) | 19.6 yd³ |
Struck | 14.4 yd³ |
Tailgate Heaped SAE 2:1 | 20.4 yd³ |
Tailgate Struck | 14.5 yd³ |
Forward - 1 | 5 mT/hr |
Forward - 2 | 9.4 mT/hr |
Forward - 3 | 14.4 mT/hr |
Forward - 4 | 22.1 mT/hr |
Forward - 5 | 30.7 mT/hr |
Forward - 6 | 36.3 mT/hr |
Reverse - 1 | 5.5 mT/hr |
Interior Cab | 69 dB(A) |
Note (1) | The declared dynamic operator sound pressure level is 69±2 dB(A) when "ISO 6396:2008" is used to measure the value for an enclosed cab. The measurement was conducted at 70% of the maximum cooling fans speed. The sound level may vary at different cooling fan speeds. The measurement was conducted with the cab doors and the cab windows closed. The cab was properly installed and maintained. |
Note (2) | Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in noisy environments. |
Total - Loaded | 103886 lb |
Rear Axle - Rated Load | 23699 lb |
Total - Empty | 50975 lb |
Total - Rated Load | 52910 lb |
Center Axle - Loaded | 33944 lb |
Front Axle - Rated Load | 5511 lb |
Center Axle - Rated Load | 23699 lb |
Center Axle - Empty | 10242 lb |
Rear Axle - Loaded | 33457 lb |
Front Axle - Loaded | 36484 lb |
Rear Axle - Empty | 9757 lb |
Front Axle - Empty | 30974 lb |
Side Plates | 0.43 in |
Front Plate | 0.28 in |
Base Plate | 0.51 in |
Fuel Tank | 91 gal (US) |
Cooling System | 18 gal (US) |
Hydraulic System | 29.1 gal (US) |
Engine Crankcase | 8 gal (US) |
Transmission | 10 gal (US) |
Final Drives/Differential | 33 gal (US) |
Output Transfer Gear Box | 5 gal (US) |
DEF Tank | 4 gal (US) |
Steering/Hoist Hydraulic System | 24 gal (US) |
Final Drive - Each | 1.6 gal (US) |
Raise Time | 10 s |
Lower Time | 8 s |
Lock to Lock | 4.75 seconds @ 60 rpm |
Brakes | ISO 3450 – 2011 |
Cab - FOPS | ISO 3449 Level II – 2008 |
Cab - ROPS | ISO 3471 – 2008 |
Steering | ISO 5010 – 2007 |
Type | High strength Brinell HB450 wear resistant steel |
Turning Dimensions - Inside Radius | 153 in |
Turning Dimensions - Aisle Width | 210 in |
Turning Dimensions - SAE Turning Radius | 294 in |
Turning Dimensions - Clearance Radius | 318 in |
Turning Dimensions - Steer Angle - Left/Right | 45° |
Note | Dimensions are for machines equipped with 23.5R25 tires. |
Wheel Loader: 950M - Passes | 5 |
Wheel Loader: 962M - Passes | 4-5 |
Wheel Loaders: 966M/966M XE - Passes | 4 |
Hydraulic Excavators: 336F/336F XE - Passes | 5-6 |
Wheel Loaders: 972M/972M XE - Passes | 3-4 |
Hydraulic Excavators: 349F/349F XE - Passes | 4-5 |