C15 ACERT™ Dry Manifold Engine

C15 ACERT™ Dry Manifold Engine   Well Servicing Engines

C15 ACERT™ Dry Manifold Engine

Product Specs

Dimensions

Weight
2743lb
Height
48.3in
Width
36.5in
Length
54.2in

General Specifications

Minimum Rating
440BHP
Maximum Rating
595BHP
Governor and Protection
ADEM A3
Aspiration
Turbocharged-Aftercooled
Displacement
928in³
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Rotation from Flywheel End
Counterclockwise
Stroke
6.75in
Bore
5.4in

Emissions

Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Capacity for Liquids

Cooling System
5.5gal (US)

Equipment

  • Air Inlet System
    • Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring and protection system (speed, temperature, pressure)
    • J1939 Broadcast (diagnostic, engine status, and control)
  • Cooling System
    • Thermostats and housing — outlet vertical
    • Jacket water pump — gear-driven, centrifugal, RH
    • RH front water pump inlet
    • All plugs/fittings are STOR for lines gp water
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
    • Full marmon connection, maximum load 10 kg for direct connection to turbo
  • Flywheels And Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • MEUI system
    • Fuel filter, secondary, mid-mount (LH 2 micron high performance)
    • Fuel transfer pump, LH front
    • Fuel priming pump, LH mid-mount
    • Fuel sample valve, mounted on fuel filter base
  • Lube System
    • Crankcase breather — rear valve cover
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump
    • Oil filler — LH front
    • Oil dipstick — LH front
    • Oil pump
    • Oil valve sampling — on oil filter base
  • Mounting System
    • Front support (shipping only)
  • Power Take-offs
    • Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
    • Hydraulic pump drive, SAE A, 11 tooth
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit 70-pin connector (connectors, pins, sockets)
    • Literature group owner and operator
  • Mandatory Options
    • Throttle position sensor
    • Exhaust system — front or rear
    • Flywheel housing or rear PTO
    • Primary filter/water separator

Optional Equipment

  • Transmission Arrangement
    • Transmission cooler
    • Tool set
  • Air Compressor
    • Air chambers
    • Air compressor governor
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Air lines
    • Air inlet gasket
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator wiring
    • Circuit breaker mountings
    • Alternator belt guard
  • Cooling System
    • Radiator — installed
    • Radiator — ship loose
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drives for customer-supplied radiators
    • Fan height instructions
    • Vee belts for customer-supplied radiators
    • Aftercooler lines f/u/w Caterpillar installed radiator
    • Rear-facing exhaust
    • Aftercooler lines
    • Suction fan adapters — attaches fan to fan pulley
    • Blower fan adapter — attaches fan to fan pulley
    • Blower fan
    • Suction fan
    • Fan belt tightener
    • Coolant level sensor
    • Dry charge coolant conditioners
    • Dry charge coolant conditioner element
  • Exhaust System
    • Turbo exhaust connection
    • Flexible fitting
    • Elbows
    • Flanges
    • Dry elbow

Interested In This Product?

Call Fabick
1 (800) 845-9188

Dial Your Nearest Location:

800-845-9188
Fabick MO & IL
414-461-9100
Fabick WI & MI
View All Locations