New CAT Equipment

Cat C32 Generator Set (US EPA Tier 4 / IMO III)

Cat C32 Generator Set (US EPA Tier 4 / IMO III)

Get a Quote

    • Clean Emissions Module (CEM) - Dimensions
      6 Brick U-Flow - Height
      23.5 in
      6 Brick U-Flow - Length
      85 in
      6 Brick U-Flow - Weight
      1235 lb
      6 Brick U-Flow - Width
      56.9 in
      6 Brick Z-Flow - Height
      23.5 in
      6 Brick Z-Flow - Length
      147.7 in
      6 Brick Z-Flow - Weight
      1246 lb
      6 Brick Z-Flow - Width
      43.5 in
      Dosing Cabinet - Height
      22.8 in
      Dosing Cabinet - Length
      37.4 in
      Dosing Cabinet - Weight
      209 lb
      Dosing Cabinet - Width
      18.8 in
    • Engine Specifications
      Aspiration
      Turbocharged-aftercooled aspiration
      Bore
      5.71 in
      Configuration
      Vee-12, 4-stroke-Cycle-Diesel
      Cooling
      Heat exchanger, keel or radiator cooled
      Displacement
      1959 in³
      Emissions
      U.S. EPA Tier 4 Final certified / IMO III emissions certified (SCR required)
      Generator
      SR5 - Form Wound
      Governor
      Electronic (A5 ECM)
      Oil Change Interval
      750 hrs
      Rated Engine Speed
      1800 rpm
      Refill Capacity
      Lube Oil System w/ oil filter change: 146 L (38.5 gal)
      Stroke
      6.38 in
    • Generator Set Dimensions
      Engine Dry Weight
      15721 lb/7131 kg (minimum), 21998 lb/9978 kg (maximum)
      Height
      70.4 in/1747 mm (minimum), 92.8 in/2356 mm (maximum)
      Length
      167.2 in/4245 mm (minimum), 226.1 in/5742 mm (maximum)
      Width
      59.9 in/1521 mm (minimum), 89.8 in/2280 mm (maximum)
    • Generator Set Specifications
      Frequency
      60hz
      Maximum Rating
      940 ekW
      Minimum Rating
      282 ekW
    AIR INLET SYSTEM
    • Separate circuit aftercooled (SCAC)
    • Closed crankcase fumes disposal
    CONTROL SYSTEM
    • 24V control system
    COOLING SYSTEM
    • Heat exchanger or Keel Cooling
    • Watercooled exhaust manifold and turbocharger
    • Hard seawater lines – no flexible hoses
    • Flanges for cooling connections, ANSI or DIN
    FUEL SYSTEM
    • Duplex fuel filters with hybrid fuel lines
    • Primary fuel filter with water separator installed on base frame
    GENERATORS AND GENERATOR ATTACHMENTS
    • IP23, air cooled, form wound SR5 generator offered in 440, 480 and 690V
    LUBE SYSTEM
    • Oil fill, simplex filter and dipstick
    MOUNTING SYSTEM
    • Helical spring/rubber isolated mounting for vibration and structure borne noise reduction
    GENERAL
    • Right or left hand service sides
    • Customer wiring and service tool connector
    ALARM AND PROTECTION
    • MGCP III B control panel with Cat® Alarm and Protection System
    • IP44 generator protection
    EXHAUST SYSTEM
    • Muffler
    • Water-in-fuel and exhaust temperature sensors
    • SOLAS approved spray shielding
    CHARGING SYSTEM
    • Charging alternator
    FUEL SYSTEM
    • Manual or electric fuel priming pump
    • Fuel cooler
    LUBE SYSTEM
    • Duplex oil filters
    STARTING SYSTEM
    • Starting motors – air, electric or redundant