New CAT Equipment

910M Compact Wheel Loader

The Cat® 910M Wheel Loader sets the standard for productivity, fuel efficiency and operator comfort. The improved optimized Z-bar loader linkage delivers the quick loading performance of a traditional Z-bar with the parallelism and load handling capability of a toolcarrier.

Get a Quote

    Learn more about the 910M Compact Wheel Loader

    Watch

    Product Specs

    Engine

    Net Power 97 HP
    Rated Net Power - SAE J1349 96 HP
    Rated Net Power - Rated Engine Speed 2200 r/min
    Maximum Gross Power - ISO 14396 (DIN) 101 HP
    Maximum Gross Power - ISO 14396 100 HP
    Maximum Gross Power - Maximum Engine Speed 2350 r/min
    Engine Model Cat C4.4 ACERT�
    Maximum Gross Power - SAE J1995 102 HP
    Maximum Gross Power 100 HP
    Emissions Engine meets U.S. EPA Tier 4 Final/EU Stage IV emission standards.
    Stroke 5 in
    Bore 4.13 in
    Maximum Gross Torque - ISO 14396 332 ft·lbf
    Rated Net Power - ISO 9249 (DIN) 98 HP
    Maximum Gross Torque - SAE J1995 336 ft·lbf
    Rated Net Power - ISO 9249 97 HP
    Note Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
    Displacement 268 in³

    Weights

    Operating Weight 17893 lb

    Service Refill Capacities

    Cooling System 5.7 gal (US)
    Fuel Tank 40.7 gal (US)
    Hydraulic System - Including Tank 25.9 gal (US)
    Engine Crankcase 2.3 gal (US)
    Diesel Exhaust Fluid (DEF) Tank 5 gal (US)
    Note DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
    Axles - Rear Center Differential 2 gal (US)
    Hydraulic Tank 14.5 gal (US)
    Axles - Front Center Differential 2 gal (US)
    Transmission 0.9 gal (US)

    Operating Specifications

    Rated Bucket Capacity 2.5 yd³

    Buckets

    Bucket Capacities 1.3-1.9 m3 (1.7-2.5 yd3)

    Cab

    ROPS ISO 3471:2008
    FOPS ISO 3449:2005 Level II
    Note (1) Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
    Note (4) *The measurements were conducted with the cab doors and windows closed.
    Note (3) The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 103 dB(A).
    Note (2) The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 77 dB(A).

    Loader Hydraulic System

    Hydraulic Cycle Time - Dump, at Maximum Reach 1.4 s
    Relief Pressure - Tilt Cylinder 4931 psi
    Maximum Flow - Implement Pump 32 gal/min
    Maximum Working Pressure - Implement Pump 3408 psi
    Relief Pressure - Tilt Cylinder - 3rd Function Maximum Working Pressure 3046 psi
    Hydraulic Cycle Time - Rackback 2.2 s
    Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift 5.2 s
    Hydraulic Cycle Time - Total Cycle Time 12.5 s
    Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level 3.7 s
    Maximum Flow - Implement Pump - 3rd Function, Maximum Flow 24 gal/min
    Maximum Flow - Implement Pump - 4th Function, Maximum Flow 24 gal/min
    Relief Pressure - Tilt Cylinder - 4th Function Maximum Working Pressure 3046 psi

    Transmission

    Note *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
    Forward and Reverse - Low Range, Speed Range 1* 6.3 mile/h
    Forward and Reverse - Low Range, Speed Range 2* 12.5 mile/h
    Forward and Reverse - High Range 25 mile/h

    Steering

    Steering Articulation Angle - Each Direction 40 °
    Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed 3.2 s
    Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left 3.75 turns
    Maximum Working Pressure - Steering Pump 2683 psi
    Maximum Flow - Steering Pump 17 gal/min

    Engine - Tier 4 Final/Stage IV

    Maximum Net Torque - ISO 9249 329 ft·lbf
    Maximum Net Torque - SAE J1349 325 ft·lbf

    Axles

    Front Fixed; Locking differential (standard)
    Rear Oscillating �11 degrees; Locking differential (Standard)

    Tires

    Note (3) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
    Other Choices Include 15.5-R25; 17.5-25 12PR; 17.5-25 12PR L2; 17.5-R25 XHA * L3; 17.5-R25 * L2/L3 PC RM; 17.5-25 16PR L3, 3PC Rim; 17.5-25 GY L2/L3; 17.5-25 12PR L2, SNOW; Flexport�
    Note (2) In certain applications, the loader's productive capabilities may exceed the tire's tonnes-km/h (ton-mph) capabilities.
    Note (1) Other tire choices are available. Contact your Cat dealer for details.
    Standard Size 15.5-25 12PR